|
Checking droop
Checking droop
Date: 12/31/1969
Views: 1505
|
Roughly where I thought the shocks would come up
Roughly where I thought the shocks would come up
Date: 12/31/1969
Views: 1061
|
Shorter slot on the passenger side after I decided the shocks could be run straight up, not angled.
Shorter slot on the passenger side after I decided the shocks could be run straight up, not angled.
Date: 12/31/1969
Views: 1205
|
dcp 0014
dcp 0014
Date: 12/31/1969
Views: 1008
|
Holding the new U-bolt plate based lower mount in place for testing
Holding the new U-bolt plate based lower mount in place for testing
Date: 12/31/1969
Views: 1195
|
|
See the lower mount?
See the lower mount?
Date: 12/31/1969
Views: 995
|
To build the uprights for the hoop, I hole-sawed a single piece of tube, then cut it in half on the bandsaw
To build the uprights for the hoop, I hole-sawed a single piece of tube, then cut it in half on the bandsaw
Date: 12/31/1969
Views: 1646
|
To build the uprights for the hoop, I hole-sawed a single piece of tube, then cut it in half on the bandsaw
To build the uprights for the hoop, I hole-sawed a single piece of tube, then cut it in half on the bandsaw
Date: 12/31/1969
Views: 1238
|
First mock up of the uprights
First mock up of the uprights
Date: 12/31/1969
Views: 1048
|
Checking "bump" clearance
Checking "bump" clearance
Date: 12/31/1969
Views: 1151
|
|
For the upper mounts, I hole-sawed some flat stock, which I then cut in half lengthwise to make a total of 4 tabs
For the upper mounts, I hole-sawed some flat stock, which I then cut in half lengthwise to make a total of 4 tabs
Date: 12/31/1969
Views: 1270
|
The uprights
The uprights
Date: 12/31/1969
Views: 1176
|
dcp 0023
dcp 0023
Date: 12/31/1969
Views: 4165
|
dcp 0024
dcp 0024
Date: 12/31/1969
Views: 1587
|
dcp 0025
dcp 0025
Date: 12/31/1969
Views: 1080
|
|
Welding
Welding
Date: 12/31/1969
Views: 1610
|
dcp 0027
dcp 0027
Date: 12/31/1969
Views: 998
|
dcp 0028
dcp 0028
Date: 12/31/1969
Views: 1175
|
Comparing a 7100 Remote Reservoir to a 5125 for ideas on how to affix the upper tabs
Comparing a 7100 Remote Reservoir to a 5125 for ideas on how to affix the upper tabs
Date: 12/31/1969
Views: 1350
|
After welding the mounts onto the bolt-in upright hoop.
After welding the mounts onto the bolt-in upright hoop.
Date: 12/31/1969
Views: 1372
|
|
dcp 0002
dcp 0002
Date: 12/31/1969
Views: 1917
|
dcp 0003
dcp 0003
Date: 12/31/1969
Views: 1139
|
U-bolt plates after welding the lower mounts to them. They are offset to the outside of the vehicle.
U-bolt plates after welding the lower mounts to them. They are offset to the outside of the vehicle.
Date: 12/31/1969
Views: 2932
|
Paint
Paint
Date: 12/31/1969
Views: 1248
|
Preparing to tear down one of the 7100s for revalving and a seal replacement on the reservoir
Preparing to tear down one of the 7100s for revalving and a seal replacement on the reservoir
Date: 12/31/1969
Views: 1238
|
